Just like everything else, there is a right way and a wrong way when it comes to bid bonds. You may be happy to learn from your mistakes, but these lessons can be costly. Messing up a bid bond can result in the loss of a lucrative contract. It can cause the demise of your bonding relationship, could become the basis of a lawsuit, or merely make you look bad in front of your boss. In any event, it's better to learn the easy way so... There are three things to remember when it comes to bid bonds: Underwriters view the bid bond as the first link in a chain of events that hopefully will result in the issuance of a performance bond. Therefore, the decision to provide it is predicated on the surety's ability to support the eventual P&P bond that may result. The decision is based on the potential dollar value of the contract, not the bid bond. A 10% bid bond on a $1 million proposal is not a $100,000 decision. There is such a thing as a bid bond claim. We don't "just issue" them. What Not To Do #1 Just to be sure you have the bid bond in time, you could move up the date on the Bond Request Form. The bid is really on the 25th, but you indicate the 22nd, just so they don't mess you up. Pretty clever? Actually, no. The underwriter will probably ask for a copy of the bid invitation and see the actual date. Plus, they may have other bidders on the same job, and the info is probably available online, etc. Such tactics can hurt your rapport with the surety. You want to be cute, but not in this way. What Not To Do #2 It is common for sureties to indicate a maximum dollar amount (bonding line) that they will support on a single contract. Let's say it is $1 million per job. If your bid calculation for an upcoming project is firm at $1.25 million, what do you do? Another scenario: You expected to not exceed $1 million but a sub or supplier price comes in higher than anticipated at the very last minute! Lower the bid to $1 million to fit the line and hope to make up the difference on the project? Request the bond for $1 million but put in the bid for $1.25 million, then claim it was a communication error? Use the $1 million bid bond, then plan to get a different surety that will provide a $1.25 million P&P bond? Don't bid the job? There is really no way to "sneak in" a bid for a higher amount. The system is set up to prevent this. In addition, the surety may issue a capped bid bond, which means it is void if used for more than the approved project amount. The best option is to make a special presentation to the underwriter and gain support for $1.25 million. All the other options can have bad outcomes. What Not To Do #3 A new project opportunity pops up and there isn't enough time to get a bid bond. Is it best to: Submit the bid with no security and hope to provide it later? Use a check instead of a bid bond, and hope to exchange the bond for the check after the bid opening? Don't bid the job? A possible solution could be an electronic copy of the bid bond (which can be printed out and signed / sealed by the contractor). Most obligees will accept this, at least temporarily. We don't recommend bidding with a check unless the surety has indicated their support of the project. Without that commitment in hand, the failure to provide a P&P bond could cause loss of the bid security and contract. Bad outcome! What Not To Do #4 The proposals have been turned in and the bid results are known. You are low bidder, REAL low. Bids that are more than 10% below the second bidder raise a red flag for the surety and could prevent their support of the P&P bond. What to do? Report the bid results but "fix up" the numbers to eliminate the spread in excess of 10%. Report the results and hope for approval. Withdraw your bid. This actually happens pretty often. We think the best approach is to step back and review the bid calculation, the bid results and the relative competitiveness of the proposers. If you find an error in the calculation, it may be prudent to quickly withdraw the bid and avoid a losing contract. The bid results may show a cluster of bidders above the second bidder. In these cases, the low bid may be acceptable if it is not more than 15% below the average of the second and third bidders. (The point is to avoid an underpriced project, bad for the contractor and any surety that may have to step in to complete it.) It is also possible that the low bidder has a unique advantage over the other companies such as closer to the project, specialized equipment, prior experience, materials on hand, or a special relationship with the architect or owner. The key is to make a written presentation to the underwriter explaining these details. We hope these tips help as the new bidding season unfolds. Oh, here's the third thing to remember: Treat bid bonds as the first step in a process, and above all, protect your surety relationship. It is more important than any one bond or project. Steve Golia is an experienced provider of bid and performance bonds for contractors. For more than 30 years he has specialized in solving bond problems for contractors, and helping them when others failed. The experts at Bonding Pros have the underwriting talent and market access you need. This is coupled with spectacular service and great accessibility. Article Source: http://EzineArticles.com/9302712